Guía BEAMA para Dispositivos de Detección de Fallas de Arco

Guía BEAMA para Dispositivos de Detección de Fallas de Arco

La función de un dispositivo de detección de fallos de arco (AFDD) es determinar si existe un arco producido por conexiones terminales sueltas, cables engarzados y/o clavos que perforan conductores. Un arco puede durar muchos meses con una corriente demasiado baja para accionar un interruptor automático o sin una fuga a tierra, y la primera indicación de este tipo de fallo suele ser un incendio.

Respuesta rápida: El AFDD monitorea las formas de onda de corriente y voltaje para detectar la firma de alta frecuencia de un arco y aísla (desconecta) el circuito automáticamente cuando detecta este tipo de fallo. Los AFDD deben ser fabricados y probados según la Norma Internacional para dispositivos de detección de fallos de arco (IEC 62606) y pueden adquirirse como un dispositivo independiente o combinado con un RCD en un solo módulo. El precio típico de un AFDD está entre £30 y £120 (sin incluir la instalación).

Las secciones restantes de este documento proporcionan una cobertura completa de la guía y explican qué se cubre en la guía, qué puede detectar un AFDD que otros dispositivos no pueden, cómo detecta un AFDD, dónde los Reglamentos de Instalación requieren AFDD, en qué forma están disponibles los dispositivos, comparaciones con otros dispositivos similares, marcas para verificar la conformidad, costos, disparos intempestivos, cómo elegir entre una unidad independiente o una combinada, y dónde puede encontrar nuestros dispositivos en su área local, además de una lista de verificación para la puesta en marcha e instalación de AFDD.

Qué cubre la Guía BEAMA y por qué existe

La guía BEAMA se desarrolló en respuesta al requisito bajo la próxima Enmienda 2 a la Norma Británica 7671 que los AFDD deben instalarse en circuitos de enchufes con una clasificación de 32 A o menos dentro de locales residenciales de alto riesgo; las diferencias entre AFDD, RCBO y RCCB y el AFCI en Norteamérica no son tan fáciles de establecer como muchas personas presumen al evaluar catálogos.

La guía BEAMA fue desarrollada por la Asociación Británica de Fabricantes Electrotécnicos para abordar los problemas asociados con la introducción de los Reglamentos de Instalación revisados y los nuevos AFDD, que estaban siendo enviados por los fabricantes e instalados por los contratistas. En ambos lados, se necesitaba un lenguaje común para facilitar la comunicación. La guía explica:

  • Cómo funcionan los AFDD y qué hacen
  • Cómo se prueban los AFDD
  • Cuáles son las normas aplicables para los AFDD
  • Cómo seleccionar e instalar un AFDD

El EMF (Campo Electromagnético) es una tecnología no intuitiva; por lo tanto, se desarrolló una guía en lugar de solo una hoja de datos o catálogo para los AFDD. Por ejemplo, el propósito de un interruptor automático es proteger contra sobrecargas y cortocircuitos, lo cual es fácil de entender visualmente. En contraste, el AFDD protege contra un modo de fallo que no tiene ninguna señal visible de daño hasta después de que ha ocurrido un incendio. La decisión de instalar un AFDD se basa en una evaluación de riesgo en lugar de cálculos matemáticos simples.

La guía también proporciona una justificación comercial porque los AFDD cuestan varias veces más que un interruptor automático miniatura (MCB). Una forma más sencilla de explicar la evitación de riesgos asociada con los AFDD frente a los MCB es utilizar un documento publicado por una organización industrial en lugar de un folleto del fabricante al solicitar la justificación para la compra de AFDD.

Lo que un AFDD detecta que otros dispositivos no pueden

Un dispositivo de detección de fallas de arco (AFDD) detecta arcos en un circuito debido a la falla de un conductor en serie con una carga eléctrica. Cuando un conductor falla, los arcos creados entre los extremos rotos mantienen el flujo de corriente a través del circuito, aunque a un nivel reducido, y en algunos casos, la cantidad total de corriente que fluye a través del circuito permanece por debajo de la capacidad térmica del interruptor automático indefinidamente. Un tornillo de terminal suelto, un cable de extensión dañado o un cable cortado durante la instalación pueden producir un patrón similar.

Un arco paralelo ocurre cuando dos cables forman un arco que va de línea a neutro o de línea a tierra y produce suficiente corriente para disparar un interruptor. La versión más peligrosa de esto es la alta resistencia entre los dos cables; la alta impedancia limita la corriente a través de las fallas a un nivel que un interruptor puede tolerar, pero el arco continúa.

Un dispositivo de corriente residual no detectará estos arcos a menos que tengan fuga a tierra; por eso los AFDD llenan ese vacío. Detectan el arco en sí y no la consecuencia del arco (es decir, el incendio), por eso estos dispositivos se comercializan como protección contra incendios eléctricos y no como protección contra sobrecargas o descargas eléctricas.

La interruptor detector de arco funciona bajo el mismo principio y, explicado desde el lado de la instalación, distingue entre arcos en serie y arcos paralelos.

Dentro del dispositivo: detección, procesamiento y disparo

El dispositivo muestrea continuamente la forma de onda de corriente utilizando un pequeño transformador de corriente o un shunt. Un microcontrolador identifica características que pueden indicar un arco, incluyendo el contenido de alta frecuencia de la forma de onda, un aumento o disminución brusca de corriente, la ‘pausa’ característica en cada medio ciclo y la aleatoriedad de la firma de detección de arco.

El microcontrolador luego compara las características extraídas con el modelo actual de arco definido a 230 Voltios y 50 Hertz y contra una base de datos de patrones que no deberían causar disparo en el dispositivo. Dentro del segundo grupo se encuentran una serie de desafíos técnicos presentados por el ruido de alta frecuencia causado por productos comunes – atenuadores, motores con escobillas, fuentes de alimentación conmutadas y taladros – que no producen un arco eléctrico.

Como resultado del requisito, el dispositivo debe emplear un solenoide que abra los contactos del relé después de que se cumpla el tiempo de disparo definido. Al igual que con el ruido de alta frecuencia, el tiempo de disparo no es instantáneo porque el dispositivo está discerniendo un patrón en lugar de medir un nivel de voltaje o corriente. El tiempo adicional proporcionado permite al dispositivo ignorar un evento transitorio pero aún así conservar la capacidad de detectar un evento real de arco eléctrico.

Descrito en la norma IEC 62606 están los tipos de “formas de onda de prueba” que el dispositivo debe soportar y no soportar, y prohíbe específicamente que el dispositivo se dispare debido a la corriente de irrupción.

Dónde los Reglamentos de Cableado Requieren AFDDs

Dónde los Reglamentos de Cableado Requieren AFDDs

La enmienda 2:2022 de BS 7671 requiere que todos los circuitos finales monofásicos con una clasificación de hasta 32 A que alimenten tomas de corriente ubicadas dentro de propiedades residenciales de mayor riesgo – casas de ocupación múltiple, alojamientos para estudiantes, residencias de cuidado y propiedades similares que tengan dormitorios – estén equipados con AFDD. Este requisito se encuentra en el Reglamento 421.1.7 y es aplicable a todas las instalaciones nuevas y modificaciones, pero no a todas las instalaciones existentes.

El alcance está intencionadamente limitado y no se refiere a “todas las viviendas” como muchas personas piensan. No existe un requisito en Inglaterra para que cada casa esté provista de AFDDs. En 2019, las normas de construcción de Escocia exigieron el uso de AFDDs para circuitos de tomas en edificios nuevos. Por lo tanto, las especificaciones para circuitos de tomas en Glasgow y Manchester serán diferentes.

Otro país, Estados Unidos, utiliza un enfoque alternativo para proporcionar protección contra fallas de arco a todos menos a un pequeño número de circuitos derivados. Ha utilizado su Código Eléctrico Nacional y su estándar AFCI en lugar de IEC 62606 como medio para proporcionar esta protección. Hay otros países europeos, como Alemania, que también tienen requisitos similares para ciertos tipos de ocupación. El principio subyacente para todos estos países es que el requisito de protección contra fallas de arco se basa en el grado de riesgo de incendio asociado con estructuras habitables.

Tipos y Factor de Forma

El área de mercado cubre tres tipos y, como tal, al elegir un tipo, normalmente se basará en la cantidad de espacio en el panel que ocupará más que en el nivel de protección que proporcionará.

Formato Ancho Lo que contiene Dónde se utiliza
AFDD independiente 1 módulo Detección de arco con mecanismo de disparo A continuación de un MCB o RCBO existente
AFDD + MCB 2 módulos Detección de arco con protección de corriente Circuitos nuevos sin RCBOs
AFDD + MCB 2 módulos Detección de arco, protección de corriente y corriente residual Más comúnmente usado para circuitos de tomas

El formato más común para especificación es AFDD + RCBO ya que la última categoría cubre todas las necesidades asociadas con circuitos de tomas. Además, usar un dispositivo para protección tanto de corriente como de corriente residual ahorra tanto un terminal como un módulo.

In our range of products the combined format is the AFDD7LE device in the 1P+N configuration that is used for all single-phase final circuits.

An AFDD is specifically designed for the detection of arcs in a circuit, which can cause fires. Its function is to provide additional safety protection and prevent loss of life and property.

AFDD, RCCB, RCBO and MCB What Each One Detects

AFDD, RCCB, RCBO and MCB: What Each One Detects

The significance of an AFDD, as compared to an RCCB, is that both devices provide the same protection against electrocution or electrical shock; however, the way in which they operate and the conditions prompting a trip vary. The difference between an AFDD and an RCCB is the “signature” of an arc. The current waveform of an arc is distinctive, therefore the AFDD is able to detect that signature. In situations where the cable insulation is damaged and an arc exists in the cable, it may not leak to earth, thus the RCCB will not detect such an event.

AFDD, RCCB and MCB are the three devices to compare. The purpose for which each of these devices was designed was to protect a circuit from overcurrent – that is to say, protect the conductors against overloads and short circuits.

The MCB provides protection by tripping the circuit when the temperature of the conductor exceeds the temperature at which the insulation material becomes damaged. This is achieved by the MCB being equipped with a bimetallic strip that reacts to the heat generated by the overload to trip the device. The RCCB protects against electric shock and is connected to the earth with a residual current device (RCD). Once the RCCB detects that the current going out of the circuit differs from the current going back to the supply, it trips and disconnects the supply.

To recap,

  • An AFDD is designed to provide additional protection to a circuit against potential fire hazards caused by arcing.
  • An RCCB is designed to provide protection against electric shock by monitoring the difference in current between phases and earth connections.
  • An MCB provides protection to conductors from overheating and short-circuiting.

AFDDs and RCBOs are two distinct types of devices, and therefore, the key difference between them is quite simple: there are no arc detection capabilities with an RCBO and an AFDD will only detect arcs if it is combined with an RCBO. You will find a further comparison between the two devices in an article regarding RCCBs versus RCBOs on the residual current side of things, and that article is especially relevant today as it highlights how many of the circuits that are used in homes today require both types of devices, so there is a debate on whether to purchase one device or two devices to fulfil the requirements.

Ratings and Markings to Check

Devices must meet six requirements to be deemed suitable. The standard, which is either IEC 62606 or the EN equivalent, should not be an endorsement, but rather, a specific number listed. The rated current for an AFDD will be typically between 6 A and 63 A; the rated voltage and frequency will typically be 230 V at 50 Hz (for the European market); and the rated conditional short circuit current is the fault current that will be applied to the device when using the type of upstream breaker specified.

If the AFDD is paired with an RCBO, it will typically detect a residual current of 30 mA for socket circuits. With an MCB, the AFDD will have more electronic components, and this means the terminal space will generally be less, which is important when using a 6 mm² cable.

The seventh requirement for an AFDD is not included on the device’s label. However, this information will appear on the certification document and will detail the testing done on the arc detection capability of the device. The test done to verify arc detection ability would be a type test to IEC 62606, not a routine test. A device that only has a routine test certificate and has not been proven to detect arcs cannot be relied upon to detect anything.

When considering the cost associated with AFDDs, it is commonly assumed that the installation will be more costly than the device itself, which leads to clients being surprised at the end of a quote.

What They Cost, and What the Installation Adds

An itemised breakdown of the costs associated with AFDDs is as follows:

Artículo Costo típico Nota
AFDD independiente £30 to £70 Per module; will require an additional device to provide residual current protection
AFDD + MCB (2 modules) £45 to £90 The MCB does not provide residual current protection
AFDD + RCBO (2 modules) £60 to £120 The normal choice for circuits providing sockets
Board increase £150 to £400 Increasing board size or installing a new board
Tested and certified £80 to £250 A fixed price for each installation

The issue with the costs associated with the board increase is that, when trying to install AFDDs protecting socket outlets from all ten circuits in a ten-way RCBO board, you will require the installation of a new board rather than the installation of ten additional devices; therefore, you will initially have a larger outlay than the device prices alone suggest.

The differential in price of devices when AFDDs are compared to RCBOs will be between £30 to £60 per board way for the next 20 years, allowing approximately a few £ a year for having AFDD protection against a deadly mode of failure, as described in the guide from BEAMA and the reason for the necessity for them.

What Is Nuisance Tripping, and What Causes It?

If an AFDD trips on a normal load, the AFDD has classified a waveform incorrectly, and there is a defined method of how this can occur; specifically, dimmers, when operated at a low wattage, produce a chopped waveform with a high frequency, which is similar to the waveform produced during an arc. Brush motors like the ones in power tools or vacuum cleaners typically generate continuous arcing from the brushes by design. Similar capabilities can be found within the output of poor filter quality on switching mode power supplies (SMPS).

While there are many possible explanations for nuisance tripping, older installations offer additional reasons. When the neutral for two circuits is shared, or if there was ever an intermittent ‘real’ arcing due to poor connection quality, or of damaged insulation in between the arcing cable, these types of faults exist and the device is justified in tripping, thus a nuisance trip must not be assumed as a fault with the device and must be explored further.

The diagnostic process employed will be the same as that used with an RCBO. To isolate your loads, you must first reset the device and connect them back one at a time. If a tripped device continues when a specific appliance is connected, then the appliance and/or its cord are at fault. If a tripped device continues without anything connected, then the wiring is at fault. If a tripped device continues only in wet weather conditions, then moisture penetration into the outdoor circuit must exist.

Choosing Between Standalone and Combined

Choosing Between Standalone and Combined

Four different variables will determine whether to choose between standalone devices versus combined devices:

  1. A socket outlet circuit must provide residual current protection, either combined with an AFDD within a single unit or separate.
  2. An existing circuit that already possesses an RCBO, and now also needs an AFDD, must therefore have a stand-alone AFDD added.
  3. In a board containing zero spare ways, a new installation of whatever configuration must take place – therefore providing the specification of the board would be paramount versus the device.
  4. Because of the spark-like sounds produced in some applications (e.g., a woodworking shop with tools built with brushes) the load circuit may have to have an AFDD on a different circuit than where the tools are plugged in.

As such, AFDD’s use of the RCBO format on most current boards provides a reference for the combined device. The footprint and terminal arrangement of each type of AFDD matches as such; therefore, any project that standardises on the same footprint can add the arc protection without the need to redesign the board.

Where HUYU Fits into this Picture

We manufacture the AFDD in the combined 1 phase + Neutral format, with the MCB and RCBO in the same footprint. The construction of the AFDD complies with IEC 62606 for the function of detection of arc and IEC 61009-1 for the function of overcurrent and residual. The combination is what actually will provide a socket circuit in a home.

For a specification, we can supply the type test report for arc detection, the residual current test data, and the conditional short-circuit rating with the upstream device used in the test. These three documents are what a certifying body or inspector will require and what a low-cost AFDD typically cannot provide.

In terms of mini interruptores automáticos, there are circuits throughout most buildings that do not require arc protection. The majority of circuits will not need an AFDD, and specifying an AFDD for every circuit means spending money where the potential risk does not warrant such an expense.

Checklist to Comply with Specifications

There are 5 items that are to be included when making a specification, to conform to IEC 62606. These include the formats of the device (combined or stand-alone), the rated current and residual current sensitivity if combined; the conditional short circuit rating (the upstream device that the combined device assumes is used); and type test evidence (evidence of testing) to be included with the order, not requested.

At the time of commissioning, 3 checks are required. These checks include the test button to verify the operation of the trip mechanism, however, not the operation of the arc detection mechanism; the residual current test (if a combined device) with an external tester, not the test button; and a load test with appliances that may be connected to the device, as it is better to discover if a dimmer switch or brushed motor will trip the device upon delivery rather than at 12:00 am.

The 4th check is documentation. A schedule is required for the installation to be maintainable. The schedule should indicate which devices are connected to which circuits and when the last test was performed. An AFDD is a safety device with a defined service life. A device that has never been tested is a device that cannot be vouched for.

Preguntas Frecuentes

What Are Arc Fault Detection Devices?

They are devices designed to detect high-frequency signatures from electrical arcs generating heat to ignite surrounding combustibles in the vicinity of an electrical circuit and automatically isolate the electrical circuit from its electrical supply prior to combustion. They are specified to the IEC 62606 standards; they are available as individual components or as part of an RCBO; and they provide protection for an arc or failure mode that cannot be detected by either the trip or residual current device.

What Methods Are Used to Detect Arc Faults?

Arc faults are detected by periodically sampling the current flowing in the circuit and examining the characteristics of the sampled waveform for certain defined features based upon high-frequency contents, sudden changes in current patterns, the stop time between cycles and whether the sampled waveform exhibits randomness in its pattern. A microcontroller compares these characteristics to those of a) the arc detection system and b) the associated load that is not supposed to cause a trip.

What Is an AFCI?

The AFCI (Arc Fault Circuit Interrupter) is the equivalent of an AFDD as defined in the North American UL 1699 standard. An AFCI performs the same function as an AFDD, but is tested to a different standard and rated to operate at 120 Volts in North American branch circuits. Therefore, AFCIs and AFDDs may not be replaced with one another or by a device that complies with one of the two standards.

Which Rooms Need AFCI Protection?

In England, the BS 7671 amendment 2 requires the installation of AFDD protection on socket circuits of 32 A or less at greater risk of electrical shock, which occur generally in HMOs, student accommodation and care homes but do not need to be installed in each room of every house. In Scotland, new houses must have an AFDD fitted as part of the electrical installation. In the United States of America, the National Electrical Code requires that most dwelling branch circuits must be protected by AFCIs.

Is an AFDD Used Instead of an RCBO?

No. AFDDs are designed to detect arcs in the circuit and an RCBO detects overloads, shortages and earth leakage of current. Typically, socket circuits will require both devices, which is why a combination of an AFDD and an RCBO in a single module is most commonly used. Standalone AFDDs are generally installed on the load side of an RCBO.

Why Does My AFDD Keep Tripping?

AFDD tripping can be caused by a load that creates arc-like sounds; e.g. a dimmer switch on a low setting; a vacuum cleaner; or a power drill; or from an actual fault, such as a loose connection or damaged cable. You can isolate all loads and reconnect them one by one to determine which appliance is causing the trip. If the trip occurs when nothing is connected, the problem may lie with the wiring.

Referencias

Conclusión

AFDDs are the only devices within a circuit board that detect the arc itself rather than the current produced by the arc. This is what enables AFDDs to detect a failing terminal connection that a circuit breaker would ignore, and which cannot be detected by an RCD. That is why the requirement was introduced into the regulations for buildings where persons sleep. The decision is based on the choice of format and proof. The combination of an AFDD and an RCBO can create a single module that protects a socket circuit, and the only proof that these detection devices work is the fulfillment of the type test to IEC 62606; everything else on the label is simply a rating, which is a much less rigorous process than testing for compliance with a standard.

 

WhatsApp
+86 181 0587 1610
Correo electrónico
info@huyu.com.cn
Facebook
huyuelectric1989
LinkedIn
HUYU Electric