Guide BEAMA des dispositifs de détection des défauts d'arc

Guide BEAMA des dispositifs de détection des défauts d'arc

La fonction d’un dispositif de détection de défaut d’arc (AFDD) est de déterminer s’il y a un arc produit par des connexions de bornes desserrées, des câbles sertis et/ou des clous traversant les conducteurs. Un arc peut durer plusieurs mois à un courant trop faible pour déclencher un disjoncteur ou sans fuite à la terre, et la première indication de ce type de défaut est généralement un incendie.

Réponse rapide : L’AFDD surveille les formes d’onde du courant et de la tension pour détecter la signature haute fréquence d’un arc et isole (déconnecte) automatiquement le circuit lorsqu’il détecte ce type de défaut. Les AFDD doivent être fabriqués et testés conformément à la norme internationale pour les dispositifs de détection de défaut d’arc (IEC 62606) et peuvent être achetés soit comme dispositif autonome, soit combinés avec un DDR dans un seul module. Le prix typique d’un AFDD se situe entre 30 £ et 120 £ (hors installation).

Les sections restantes de ce document fournissent une couverture complète du guide et expliquent ce qui est couvert dans le guide, ce qu’un AFDD peut détecter que d’autres dispositifs ne peuvent pas, comment un AFDD détecte, où les règlements de câblage exigent des AFDD, sous quelle forme les dispositifs sont disponibles, des comparaisons avec d’autres dispositifs similaires, les marquages à vérifier pour la conformité, les coûts, les déclenchements intempestifs, comment choisir une unité autonome ou une unité combinée, et où vous pouvez trouver nos dispositifs dans votre région, ainsi qu’une liste de contrôle pour la mise en service et l’installation des AFDD.

Ce que couvre le guide BEAMA, et pourquoi il existe

Le guide BEAMA a été développé en réponse à l’exigence de l’amendement 2 à venir de la norme britannique 7671 selon laquelle les AFDD doivent être installés sur les circuits de prises de courant de 32 A ou moins dans les locaux résidentiels à haut risque ; les différences entre AFDD, RCBO & DDR et l’AFCI en Amérique du Nord ne sont pas aussi faciles à établir que beaucoup le supposent lors de l’évaluation des catalogues.

Le guide BEAMA a été développé par la British Electrotechnical Manufacturers Association pour traiter les questions liées à l’introduction des règlements de câblage révisés et des nouveaux AFDD, qui étaient expédiés par les fabricants et installés par les entrepreneurs. Des deux côtés, un langage commun était nécessaire pour faciliter la communication. Le guide explique :

  • Comment fonctionnent les AFDD et ce qu’ils font
  • Comment les AFDD sont testés
  • Quelles sont les normes applicables aux AFDD
  • Comment sélectionner et installer un AFDD

Le CEM (champ électromagnétique) est une technologie non intuitive ; par conséquent, un guide a été développé plutôt qu’une simple fiche technique ou un catalogue pour les AFDD. Par exemple, le but d’un disjoncteur est de protéger contre les surcharges et les courts-circuits, ce qui est facile à comprendre visuellement. En revanche, l’AFDD protège contre un mode de défaillance qui ne présente aucun signe visible de dommage avant qu’un incendie ne se soit produit. La décision d’installer un AFDD est basée sur une évaluation du risque plutôt que sur de simples calculs mathématiques.

Le guide fournit également une justification commerciale car les AFDD coûtent plusieurs fois plus cher qu’un disjoncteur miniature (MCB). Une manière plus simple d’expliquer l’évitement des risques associé aux AFDD par rapport aux MCB est d’utiliser un document publié par une organisation industrielle plutôt qu’une brochure de fabricant lors de la demande de justification pour l’achat d’AFDD.

Ce que détecte un AFDD que d’autres dispositifs ne peuvent pas détecter

Un dispositif de détection d’arc électrique (AFDD) détecte les arcs dans un circuit dus à la défaillance d’un conducteur en série avec une charge électrique. Lorsqu’un conducteur est défaillant, les arcs créés entre les extrémités rompues maintiennent le flux de courant à travers le circuit, bien qu’à un niveau réduit, et dans certains cas, la quantité totale de courant circulant dans le circuit reste indéfiniment inférieure à la capacité thermique du disjoncteur. Une vis de borne desserrée, un câble d’extension endommagé ou un fil coupé lors de l’installation peuvent tous produire un schéma similaire.

Un arc parallèle se produit lorsque deux fils forment un arc qui va de la phase au neutre ou de la phase à la terre et produit suffisamment de courant pour déclencher un disjoncteur. La version la plus dangereuse est une haute résistance entre les deux fils ; la haute impédance limite le courant à travers les défauts à un niveau que le disjoncteur peut tolérer, mais l’arc continue.

Un dispositif à courant résiduel ne détectera pas ces arcs à moins qu’ils ne fuient à la terre ; c’est pourquoi les AFDD comblent cette lacune. Ils détectent l’arc lui-même et non la conséquence de l’arc (c’est-à-dire l’incendie), c’est pourquoi ces dispositifs sont commercialisés comme une protection contre les incendies électriques et non comme une protection contre les surcharges ou les chocs électriques.

La disjoncteur détecteur d’arc fonctionne selon le même principe et, expliqué du côté installation, distingue entre les arcs en série et les arcs parallèles.

À l’intérieur du dispositif : détection, traitement et déclenchement

Le dispositif échantillonne en continu la forme d’onde du courant à l’aide d’un petit transformateur de courant ou d’un shunt. Un microcontrôleur identifie des caractéristiques pouvant indiquer un arc, y compris le contenu haute fréquence de la forme d’onde, une augmentation ou une diminution brusque du courant, une ‘pause’ caractéristique à chaque demi-cycle et l’aléa d’une signature de détection d’arc.

Le microcontrôleur compare ensuite les caractéristiques extraites au modèle d’arc actuel défini à 230 Volts et 50 Hertz et à une base de données de motifs qui ne devraient pas provoquer de déclenchement du dispositif. Dans ce second groupe se trouvent une série de défis techniques présentés par le bruit haute fréquence causé par des produits courants – variateurs, moteurs à balais, alimentations à découpage et perceuses – qui ne produisent pas d’arc électrique.

En raison de cette exigence, l’appareil doit utiliser un solénoïde qui ouvre les contacts du relais après que le temps de déclenchement défini est écoulé. Comme pour le bruit haute fréquence, le temps de déclenchement n’est pas instantané car l’appareil distingue un motif plutôt que de mesurer un niveau de tension ou de courant. Le temps supplémentaire accordé permet à l’appareil d’ignorer un événement transitoire tout en conservant la capacité de détecter un véritable arc électrique.

Décrit dans la norme IEC 62606 sont les types de “ formes d’onde de test ” que l’appareil doit supporter et ne doit pas supporter, et elle interdit spécifiquement que l’appareil déclenche en raison du courant d’appel.

Où les règlements de câblage exigent des AFDD

Où les règlements de câblage exigent des AFDD

L’amendement 2:2022 de la norme BS 7671 exige que tous les circuits finaux monophasés jusqu’à 32 A alimentant des prises de courant situées dans des propriétés résidentielles à risque accru – maisons à occupation multiple, logements étudiants, maisons de retraite et propriétés similaires comportant des locaux de couchage – soient équipés d’AFDD. Cette exigence figure dans le Règlement 421.1.7 et s’applique à toutes les nouvelles installations et modifications, mais pas à toutes les installations existantes.

La portée est volontairement limitée et ne fait pas référence à “ tous les logements ” comme beaucoup le pensent. Il n’y a pas d’exigence en Angleterre pour que chaque maison soit équipée d’AFDD. En 2019, les normes de construction écossaises ont rendu obligatoire l’utilisation d’AFDD pour les circuits de prises dans les nouveaux bâtiments. Par conséquent, les spécifications pour les circuits de prises à Glasgow et Manchester seront différentes.

Un autre pays, les États-Unis, utilise une approche alternative pour fournir une protection contre les arcs électriques à tous les circuits dérivés sauf un petit nombre. Il utilise son National Electrical Code et sa norme AFCI plutôt que la norme IEC 62606 comme moyen de fournir cette protection. D’autres pays européens, comme l’Allemagne, ont également des exigences similaires pour certains types d’occupation. Le principe sous-jacent pour tous ces pays est que l’exigence de protection contre les arcs est basée sur le degré de risque d’incendie associé aux structures habitables.

Types et format

Le marché couvre trois types et, en tant que tel, le choix d’un type sera le plus souvent basé sur l’espace occupé dans le tableau plutôt que sur le niveau de protection qu’il fournira.

Format Largeur Ce qu’il contient Où il est utilisé
AFDD autonome 1 module Détection d’arc avec mécanisme de déclenchement En aval d’un disjoncteur MCB ou RCBO existant
AFDD + disjoncteur miniature (MCB) 2 modules Détection d’arc avec protection contre le courant Nouveaux circuits sans RCBO
AFDD + disjoncteur différentiel à courant résiduel avec protection contre les surcharges (RCBO) 2 modules Détection d’arc, protection contre le courant et courant résiduel Le plus couramment utilisé pour les circuits de prises

Le format le plus courant pour la spécification est AFDD + RCBO car la dernière catégorie couvre tous les besoins associés aux circuits de prises. De plus, l’utilisation d’un seul appareil pour la protection contre le courant et le courant résiduel permet d’économiser à la fois une borne et un module.

In our range of products the combined format is the AFDD7LE device in the 1P+N configuration that is used for all single-phase final circuits.

An AFDD is specifically designed for the detection of arcs in a circuit, which can cause fires. Its function is to provide additional safety protection and prevent loss of life and property.

AFDD, RCCB, RCBO and MCB What Each One Detects

AFDD, RCCB, RCBO and MCB: What Each One Detects

The significance of an AFDD, as compared to an RCCB, is that both devices provide the same protection against electrocution or electrical shock; however, the way in which they operate and the conditions prompting a trip vary. The difference between an AFDD and an RCCB is the “signature” of an arc. The current waveform of an arc is distinctive, therefore the AFDD is able to detect that signature. In situations where the cable insulation is damaged and an arc exists in the cable, it may not leak to earth, thus the RCCB will not detect such an event.

AFDD, RCCB and MCB are the three devices to compare. The purpose for which each of these devices was designed was to protect a circuit from overcurrent – that is to say, protect the conductors against overloads and short circuits.

The MCB provides protection by tripping the circuit when the temperature of the conductor exceeds the temperature at which the insulation material becomes damaged. This is achieved by the MCB being equipped with a bimetallic strip that reacts to the heat generated by the overload to trip the device. The RCCB protects against electric shock and is connected to the earth with a residual current device (RCD). Once the RCCB detects that the current going out of the circuit differs from the current going back to the supply, it trips and disconnects the supply.

To recap,

  • An AFDD is designed to provide additional protection to a circuit against potential fire hazards caused by arcing.
  • An RCCB is designed to provide protection against electric shock by monitoring the difference in current between phases and earth connections.
  • An MCB provides protection to conductors from overheating and short-circuiting.

AFDDs and RCBOs are two distinct types of devices, and therefore, the key difference between them is quite simple: there are no arc detection capabilities with an RCBO and an AFDD will only detect arcs if it is combined with an RCBO. You will find a further comparison between the two devices in an article regarding RCCBs versus RCBOs on the residual current side of things, and that article is especially relevant today as it highlights how many of the circuits that are used in homes today require both types of devices, so there is a debate on whether to purchase one device or two devices to fulfil the requirements.

Ratings and Markings to Check

Devices must meet six requirements to be deemed suitable. The standard, which is either IEC 62606 or the EN equivalent, should not be an endorsement, but rather, a specific number listed. The rated current for an AFDD will be typically between 6 A and 63 A; the rated voltage and frequency will typically be 230 V at 50 Hz (for the European market); and the rated conditional short circuit current is the fault current that will be applied to the device when using the type of upstream breaker specified.

If the AFDD is paired with an RCBO, it will typically detect a residual current of 30 mA for socket circuits. With an MCB, the AFDD will have more electronic components, and this means the terminal space will generally be less, which is important when using a 6 mm² cable.

The seventh requirement for an AFDD is not included on the device’s label. However, this information will appear on the certification document and will detail the testing done on the arc detection capability of the device. The test done to verify arc detection ability would be a type test to IEC 62606, not a routine test. A device that only has a routine test certificate and has not been proven to detect arcs cannot be relied upon to detect anything.

When considering the cost associated with AFDDs, it is commonly assumed that the installation will be more costly than the device itself, which leads to clients being surprised at the end of a quote.

What They Cost, and What the Installation Adds

An itemised breakdown of the costs associated with AFDDs is as follows:

Article Coût typique Remarque
AFDD autonome £30 to £70 Per module; will require an additional device to provide residual current protection
AFDD + MCB (2 modules) £45 to £90 The MCB does not provide residual current protection
AFDD + RCBO (2 modules) £60 to £120 The normal choice for circuits providing sockets
Board increase £150 to £400 Increasing board size or installing a new board
Tested and certified £80 to £250 A fixed price for each installation

The issue with the costs associated with the board increase is that, when trying to install AFDDs protecting socket outlets from all ten circuits in a ten-way RCBO board, you will require the installation of a new board rather than the installation of ten additional devices; therefore, you will initially have a larger outlay than the device prices alone suggest.

The differential in price of devices when AFDDs are compared to RCBOs will be between £30 to £60 per board way for the next 20 years, allowing approximately a few £ a year for having AFDD protection against a deadly mode of failure, as described in the guide from BEAMA and the reason for the necessity for them.

What Is Nuisance Tripping, and What Causes It?

If an AFDD trips on a normal load, the AFDD has classified a waveform incorrectly, and there is a defined method of how this can occur; specifically, dimmers, when operated at a low wattage, produce a chopped waveform with a high frequency, which is similar to the waveform produced during an arc. Brush motors like the ones in power tools or vacuum cleaners typically generate continuous arcing from the brushes by design. Similar capabilities can be found within the output of poor filter quality on switching mode power supplies (SMPS).

While there are many possible explanations for nuisance tripping, older installations offer additional reasons. When the neutral for two circuits is shared, or if there was ever an intermittent ‘real’ arcing due to poor connection quality, or of damaged insulation in between the arcing cable, these types of faults exist and the device is justified in tripping, thus a nuisance trip must not be assumed as a fault with the device and must be explored further.

The diagnostic process employed will be the same as that used with an RCBO. To isolate your loads, you must first reset the device and connect them back one at a time. If a tripped device continues when a specific appliance is connected, then the appliance and/or its cord are at fault. If a tripped device continues without anything connected, then the wiring is at fault. If a tripped device continues only in wet weather conditions, then moisture penetration into the outdoor circuit must exist.

Choosing Between Standalone and Combined

Choosing Between Standalone and Combined

Four different variables will determine whether to choose between standalone devices versus combined devices:

  1. A socket outlet circuit must provide residual current protection, either combined with an AFDD within a single unit or separate.
  2. An existing circuit that already possesses an RCBO, and now also needs an AFDD, must therefore have a stand-alone AFDD added.
  3. In a board containing zero spare ways, a new installation of whatever configuration must take place – therefore providing the specification of the board would be paramount versus the device.
  4. Because of the spark-like sounds produced in some applications (e.g., a woodworking shop with tools built with brushes) the load circuit may have to have an AFDD on a different circuit than where the tools are plugged in.

As such, AFDD’s use of the RCBO format on most current boards provides a reference for the combined device. The footprint and terminal arrangement of each type of AFDD matches as such; therefore, any project that standardises on the same footprint can add the arc protection without the need to redesign the board.

Where HUYU Fits into this Picture

We manufacture the AFDD in the combined 1 phase + Neutral format, with the MCB and RCBO in the same footprint. The construction of the AFDD complies with IEC 62606 for the function of detection of arc and IEC 61009-1 for the function of overcurrent and residual. The combination is what actually will provide a socket circuit in a home.

For a specification, we can supply the type test report for arc detection, the residual current test data, and the conditional short-circuit rating with the upstream device used in the test. These three documents are what a certifying body or inspector will require and what a low-cost AFDD typically cannot provide.

In terms of disjoncteurs miniatures, there are circuits throughout most buildings that do not require arc protection. The majority of circuits will not need an AFDD, and specifying an AFDD for every circuit means spending money where the potential risk does not warrant such an expense.

Checklist to Comply with Specifications

There are 5 items that are to be included when making a specification, to conform to IEC 62606. These include the formats of the device (combined or stand-alone), the rated current and residual current sensitivity if combined; the conditional short circuit rating (the upstream device that the combined device assumes is used); and type test evidence (evidence of testing) to be included with the order, not requested.

At the time of commissioning, 3 checks are required. These checks include the test button to verify the operation of the trip mechanism, however, not the operation of the arc detection mechanism; the residual current test (if a combined device) with an external tester, not the test button; and a load test with appliances that may be connected to the device, as it is better to discover if a dimmer switch or brushed motor will trip the device upon delivery rather than at 12:00 am.

The 4th check is documentation. A schedule is required for the installation to be maintainable. The schedule should indicate which devices are connected to which circuits and when the last test was performed. An AFDD is a safety device with a defined service life. A device that has never been tested is a device that cannot be vouched for.

Questions Fréquemment Posées

What Are Arc Fault Detection Devices?

They are devices designed to detect high-frequency signatures from electrical arcs generating heat to ignite surrounding combustibles in the vicinity of an electrical circuit and automatically isolate the electrical circuit from its electrical supply prior to combustion. They are specified to the IEC 62606 standards; they are available as individual components or as part of an RCBO; and they provide protection for an arc or failure mode that cannot be detected by either the trip or residual current device.

What Methods Are Used to Detect Arc Faults?

Arc faults are detected by periodically sampling the current flowing in the circuit and examining the characteristics of the sampled waveform for certain defined features based upon high-frequency contents, sudden changes in current patterns, the stop time between cycles and whether the sampled waveform exhibits randomness in its pattern. A microcontroller compares these characteristics to those of a) the arc detection system and b) the associated load that is not supposed to cause a trip.

What Is an AFCI?

The AFCI (Arc Fault Circuit Interrupter) is the equivalent of an AFDD as defined in the North American UL 1699 standard. An AFCI performs the same function as an AFDD, but is tested to a different standard and rated to operate at 120 Volts in North American branch circuits. Therefore, AFCIs and AFDDs may not be replaced with one another or by a device that complies with one of the two standards.

Which Rooms Need AFCI Protection?

In England, the BS 7671 amendment 2 requires the installation of AFDD protection on socket circuits of 32 A or less at greater risk of electrical shock, which occur generally in HMOs, student accommodation and care homes but do not need to be installed in each room of every house. In Scotland, new houses must have an AFDD fitted as part of the electrical installation. In the United States of America, the National Electrical Code requires that most dwelling branch circuits must be protected by AFCIs.

Is an AFDD Used Instead of an RCBO?

No. AFDDs are designed to detect arcs in the circuit and an RCBO detects overloads, shortages and earth leakage of current. Typically, socket circuits will require both devices, which is why a combination of an AFDD and an RCBO in a single module is most commonly used. Standalone AFDDs are generally installed on the load side of an RCBO.

Why Does My AFDD Keep Tripping?

AFDD tripping can be caused by a load that creates arc-like sounds; e.g. a dimmer switch on a low setting; a vacuum cleaner; or a power drill; or from an actual fault, such as a loose connection or damaged cable. You can isolate all loads and reconnect them one by one to determine which appliance is causing the trip. If the trip occurs when nothing is connected, the problem may lie with the wiring.

Références

Conclusion

AFDDs are the only devices within a circuit board that detect the arc itself rather than the current produced by the arc. This is what enables AFDDs to detect a failing terminal connection that a circuit breaker would ignore, and which cannot be detected by an RCD. That is why the requirement was introduced into the regulations for buildings where persons sleep. The decision is based on the choice of format and proof. The combination of an AFDD and an RCBO can create a single module that protects a socket circuit, and the only proof that these detection devices work is the fulfillment of the type test to IEC 62606; everything else on the label is simply a rating, which is a much less rigorous process than testing for compliance with a standard.

 

WhatsApp
+86 181 0587 1610
Email
info@huyu.com.cn
Facebook
huyuelectric1989
LinkedIn
HUYU Électrique